Book An Estimate Now

 

 

Every person maintains their own notions with regards to Installing A Bathtub.

Mounting a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably challenging task. If the old bathtub is easily accessible, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will need an assistant to move out the old bathtub as well as set in the brand-new one. See to it you have qualified on your own for the work as well as are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you may need a specialist plumber to make tube connections.
This article will certainly help you install a brand-new bathtub in your washroom if you have currently gotten a new bathtub and do not need to transform the setup of your previous water system pipelines.
Your tools and product checklist must comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installment

First of all, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its final position.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

 

 

Mounting the Tub

Using both wood boards under its feet, put the tub in the required placement. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub till the spirit level reads degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the tub as well as also inspect the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will certainly resolve it into its final setting.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in location between the faucet and also the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former type should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bathtub

In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with moisture and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the motion experienced when the tub is in usage. The sealer can split fairly early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I came across that post about Installing A Bathtub when surfing around the search engines. Do you know somebody who is serious about the niche? Take a moment to share it. I am grateful for your time. Come back soon.

Get Started